Search for: All records

Dissolved chloride concentrations higher than seawater were observed over a broad depth range in pore water profiles from International Ocean Discovery Program Site U1517 on the Hikurangi Margin. This Cl maximum is not associated with an⁸⁷Sr/⁸⁶Sr anomaly, indicating that it is not caused by hydration reactions during ash alteration. We use a numerical modeling approach to examine possible causes for recent gas hydrate formation that can result in the observed Cl high. Our approach considers sedimentation, sea level, and bottom water temperature (BWT) changes due to glaciation as drivers for the downward migration of the base of gas hydrate stability and gas hydrate formation. The modeling results reveal that lowering of sea level during glaciation can allow methane hydrate dissociation followed by postglacial hydrate formation as sea level rises. However, BWT cooling of 2 °C during glaciation followed by warming during deglaciation would mostly counteract the impacts of sea level change. Bottom water cooling during glaciation is expected in this region and many locations worldwide. As a result, our simulations do not support the previous hypotheses of large‐scale gas hydrate dissociation due to sea level drop during glaciation, which have been proposed as triggers for widespread gas release and slope failure. Such a mechanism is only possible where BWT remains constant or increases during glaciation. Our simulations indicate that sedimentation constitutes the largest factor driving recent methane hydrate formation at Site U1517, and we suggest that sedimentation may play a larger role in gas hydrate dynamics along margins than previously recognized.

 

Abstract The Short Strip ASIC (SSA) is one of the four front-end chips designed for the upgrade of the CMS Outer Tracker for the High Luminosity LHC. Together with the Macro-Pixel ASIC (MPA) it will instrument modules containing a strip and a macro-pixel sensor stacked on top of each other. The SSA provides both full readout of the strip hit information when triggered, and, together with the MPA, correlated clusters called stubs from the two sensors for use by the CMS Level-1 (L1) trigger system. Results from the first prototype module consisting of a sensor and two SSA chips are presented. The prototype module has been characterized at the Fermilab Test Beam Facility using a 120 GeV proton beam. 

Abstract The CMS Inner Tracker, made of silicon pixel modules, will be entirely replaced prior to the start of the High Luminosity LHC period. One of the crucial components of the new Inner Tracker system is the readout chip, being developed by the RD53 Collaboration, and in particular its analogue front-end, which receives the signal from the sensor and digitizes it. Three different analogue front-ends (Synchronous, Linear, and Differential) were designed and implemented in the RD53A demonstrator chip. A dedicated evaluation program was carried out to select the most suitable design to build a radiation tolerant pixel detector able to sustain high particle rates with high efficiency and a small fraction of spurious pixel hits. The test results showed that all three analogue front-ends presented strong points, but also limitations. The Differential front-end demonstrated very low noise, but the threshold tuning became problematic after irradiation. Moreover, a saturation in the preamplifier feedback loop affected the return of the signal to baseline and thus increased the dead time. The Synchronous front-end showed very good timing performance, but also higher noise. For the Linear front-end all of the parameters were within specification, although this design had the largest time walk. This limitation was addressed and mitigated in an improved design. The analysis of the advantages and disadvantages of the three front-ends in the context of the CMS Inner Tracker operation requirements led to the selection of the improved design Linear front-end for integration in the final CMS readout chip. 

Abstract During the operation of the CMS experiment at the High-Luminosity LHC the silicon sensors of the Phase-2 Outer Tracker will be exposed to radiation levels that could potentially deteriorate their performance. Previous studies had determined that planar float zone silicon with n-doped strips on a p-doped substrate was preferred over p-doped strips on an n-doped substrate. The last step in evaluating the optimal design for the mass production of about 200 m 2 of silicon sensors was to compare sensors of baseline thickness (about 300 μm) to thinned sensors (about 240 μm), which promised several benefits at high radiation levels because of the higher electric fields at the same bias voltage. This study provides a direct comparison of these two thicknesses in terms of sensor characteristics as well as charge collection and hit efficiency for fluences up to 1.5 × 10 15 n eq /cm 2 . The measurement results demonstrate that sensors with about 300 μm thickness will ensure excellent tracking performance even at the highest considered fluence levels expected for the Phase-2 Outer Tracker. 

Two additions impacting tables 3 and 4 in ref. [1] are presented in the following. No significant impact is found for other results or figures in ref. [1].